Versalift VN-55-I Specifications
- 700 lbs. Platform Capacity
- Faster Boom Speed
- Platform Rotator Now Available
Rotation is continuous and unrestricted in either direction. This is accomplished by a hydraulic motor-driven worm and spur gear acting on a shear-ball rotation bearing. The critical bolts holding the lift to the rotation bearing and the rotation bearing to the pedestal are Gr. 8 hex-head capscrews. These critical bolts are marked with a torque-seal indicator to provide a quick means of detecting any relative movement. An eccentric ring gearbox-mounting allows for precise adjustments of the gearbox pinion clearance.
The standard fiberglass platform for the VN-55 is 24" x 48" x 42" (0.61 m x 1.22 m x 1.07 m) deep with two inside and two outside steps for easy access. The standard VN platform is end mounted and classified as twoman. Liners and vinyl covers are available for the platform.
This system is designed to use either open center or closed center hydraulic tools. The tool circuit provides 8 gpm (30 lpm) at 2250 psi (158 kg/cm2). One set of hydraulic tool ports (one pressure port and one return port) is standard at the platform.
A-frame outriggers are connected to the pedestal and are equipped complete with pilot-operated check valves, internal thermal-relief valves and separate operating controls for each outrigger. At maximum extension, the outriggers provide 150" (3.8 m) of spread and a maximum of 7" (178 mm) of penetration.
The rectangular upper boom tapers from 8" x 12" (203 mm x 305 mm) at the knuckle end to 8" x 10" (203 mm x 254 mm) at the platform end and is constructed of high-strength filament-wound epoxy resin fiberglass. The fiberglass has a gel coat and a high gloss durable urethane finish for added weather protection and water beading. The fiberglass boom is certified for 46 KV and below in accordance with Category C, ANSI A92.2-1990. The upper boom articulates 70o above horizontal or a total of 175o relative to the lower boom. A compensating system maintains the upper boom at a constant angle when raising or lowering the lower boom and mechanically prevents the upper boom from traveling over- center. The system does not use any cables and the booms can be stowed in any sequence. An upper-boom storage cradle, mounted on the lower boom assures solid boom support when the boom is stowed.
The lower boom is designed and constructed from rectangular tube 10 in. x 13 in. (254 mm x 330 mm) high strength steel for maximum strength and rigidity. The lower boom cylinder anchor located on the lower boom are considered critical and are reinforced for extra strength. Boom articulation is from horizontal to 15o past vertical. Articulation is achieved by using two double acting cylinders. Each cylinder is capable of supporting the entire rated load by itself and is equipped with two integral holding valves. In the event of a hydraulic failure the integral holding valves prevent the booms from dropping by locking the booms in position. In addition, the cylinder rod eyes are threaded and welded.
GENERAL SPECIFICATIONS ((Based on 40 in. (1.02 m) Frame Height))
|Horizontal Reach||36 ft 2 in (11.0m)|
|2-Man Platform Capacity||570 lbs (260kg)|
|Lower Boom Lift Eye Capacity||1100 lbs (500 kg)|
|Upper Boom Articulation||70° above horizontal|
|Lower Boom Articulation||0° to +15°|
|With Standard Pedestal|
|Height to Bottom of Platform||55 ft 1 in (16.8m)|
|Working Height||60 ft 1 in (18.3m)|
|Stowed Travel Height||10 ft 7 in (3.2m)|
|Weight of Lift With Outriggers||6370 lbs (2890kg)|
|Operating Pressure||2250 PSI (158 kg/cm2)|
|Flow Rate||6-1/2 GPM (24.6 lpm)|
|Filtration||10 micron return|
|100 mesh suction|
|System Type||Closed & Open center|
|Power Source||PTO Pump|
|Electrical Insulation Gap|
|Upper Boom||239 in (6.1m)|
|Lower Boom||24 in (0.6m)|